7. Tweaking, tuning and troubleshooting
This HOWTO is deprecated; the Linux RAID HOWTO is maintained as a wiki by the linux-raid community at http://raid.wiki.kernel.org/
7.1 raid-level and raidtab
Some GNU/Linux distributions, like RedHat 8.0 and possibly others,
have a bug in their init-scripts, so that they will fail to start up
RAID arrays on boot, if your /etc/raidtab has spaces or tabs before the
raid-level keywords.
The simple workaround for this problem is to make sure that the
raid-level keyword appears in the very beginning of the
lines, without any leading spaces of any kind.
7.2 Autodetection
Autodetection allows the RAID devices to be automatically recognized by the kernel at boot-time, right after the ordinary partition detection is done.
This requires several things:
- You need autodetection support in the kernel. Check this
- You must have created the RAID devices using persistent-superblock
- The partition-types of the devices used in the RAID must be set to 0xFD (use fdisk and set the type to "fd")
NOTE: Be sure that your RAID is NOT RUNNING before changing the
partition types. Use raidstop /dev/md0 to stop the device.
If you set up 1, 2 and 3 from above, autodetection should be set
up. Try rebooting. When the system comes up, cat'ing /proc/mdstat
should tell you that your RAID is running.
During boot, you could see messages similar to these:
Oct 22 00:51:59 malthe kernel: SCSI device sdg: hdwr sector= 512 bytes. Sectors= 12657717 [6180 MB] [6.2 GB] Oct 22 00:51:59 malthe kernel: Partition check: Oct 22 00:51:59 malthe kernel: sda: sda1 sda2 sda3 sda4 Oct 22 00:51:59 malthe kernel: sdb: sdb1 sdb2 Oct 22 00:51:59 malthe kernel: sdc: sdc1 sdc2 Oct 22 00:51:59 malthe kernel: sdd: sdd1 sdd2 Oct 22 00:51:59 malthe kernel: sde: sde1 sde2 Oct 22 00:51:59 malthe kernel: sdf: sdf1 sdf2 Oct 22 00:51:59 malthe kernel: sdg: sdg1 sdg2 Oct 22 00:51:59 malthe kernel: autodetecting RAID arrays Oct 22 00:51:59 malthe kernel: (read) sdb1's sb offset: 6199872 Oct 22 00:51:59 malthe kernel: bind<sdb1,1> Oct 22 00:51:59 malthe kernel: (read) sdc1's sb offset: 6199872 Oct 22 00:51:59 malthe kernel: bind<sdc1,2> Oct 22 00:51:59 malthe kernel: (read) sdd1's sb offset: 6199872 Oct 22 00:51:59 malthe kernel: bind<sdd1,3> Oct 22 00:51:59 malthe kernel: (read) sde1's sb offset: 6199872 Oct 22 00:51:59 malthe kernel: bind<sde1,4> Oct 22 00:51:59 malthe kernel: (read) sdf1's sb offset: 6205376 Oct 22 00:51:59 malthe kernel: bind<sdf1,5> Oct 22 00:51:59 malthe kernel: (read) sdg1's sb offset: 6205376 Oct 22 00:51:59 malthe kernel: bind<sdg1,6> Oct 22 00:51:59 malthe kernel: autorunning md0 Oct 22 00:51:59 malthe kernel: running: <sdg1><sdf1><sde1><sdd1><sdc1><sdb1> Oct 22 00:51:59 malthe kernel: now! Oct 22 00:51:59 malthe kernel: md: md0: raid array is not clean -- starting background reconstructionThis is output from the autodetection of a RAID-5 array that was not cleanly shut down (eg. the machine crashed). Reconstruction is automatically initiated. Mounting this device is perfectly safe, since reconstruction is transparent and all data are consistent (it's only the parity information that is inconsistent - but that isn't needed until a device fails).
Autostarted devices are also automatically stopped at shutdown. Don't worry about init scripts. Just use the /dev/md devices as any other /dev/sd or /dev/hd devices.
Yes, it really is that easy.
You may want to look in your init-scripts for any raidstart/raidstop commands. These are often found in the standard RedHat init scripts. They are used for old-style RAID, and has no use in new-style RAID with autodetection. Just remove the lines, and everything will be just fine.
7.3 Booting on RAID
There are several ways to set up a system that mounts it's root filesystem on a RAID device. Some distributions allow for RAID setup in the installation process, and this is by far the easiest way to get a nicely set up RAID system.
Newer LILO distributions can handle RAID-1 devices, and thus the kernel can be loaded at boot-time from a RAID device. LILO will correctly write boot-records on all disks in the array, to allow booting even if the primary disk fails.
If you are using grub instead of LILO, then just start grub and configure it to use the second (or third, or fourth...) disk in the RAID-1 array you want to boot off as its root device and run setup. And that's all.
For example, on an array consisting of /dev/hda1 and /dev/hdc1 where both partitions should be bootable you should just do this:
grub grub>device (hd0) /dev/hdc grub>root (hd0,0) grub>setup (hd0)
Some users have experienced problems with this, reporting that although booting with one drive connected worked, booting with both two drives failed. Nevertheless, running the described procedure with both disks fixed the problem, allowing the system to boot from either single drive or from the RAID-1
Another way of ensuring that your system can always boot is, to create
a boot floppy when all the setup is done. If the disk on which the
/boot filesystem resides dies, you can always boot from the
floppy. On RedHat and RedHat derived systems, this can be accomplished
with the mkbootdisk command.
7.4 Root filesystem on RAID
In order to have a system booting on RAID, the root filesystem (/) must be mounted on a RAID device. Two methods for achieving this is supplied bellow. The methods below assume that you install on a normal partition, and then - when the installation is complete - move the contents of your non-RAID root filesystem onto a new RAID device. Please not that this is no longer needed in general, as most newer GNU/Linux distributions support installation on RAID devices (and creation of the RAID devices during the installation process). However, you may still want to use the methods below, if you are migrating an existing system to RAID.
Method 1
This method assumes you have a spare disk you can install the system on, which is not part of the RAID you will be configuring.
- First, install a normal system on your extra disk.
- Get the kernel you plan on running, get the raid-patches and the tools, and make your system boot with this new RAID-aware kernel. Make sure that RAID-support is in the kernel, and is not loaded as modules.
- Ok, now you should configure and create the RAID you plan to use for the root filesystem. This is standard procedure, as described elsewhere in this document.
- Just to make sure everything's fine, try rebooting the system to see if the new RAID comes up on boot. It should.
- Put a filesystem on the new array (using
mke2fs), and mount it under /mnt/newroot - Now, copy the contents of your current root-filesystem (the
spare disk) to the new root-filesystem (the array). There are lots of
ways to do this, one of them is
cd / find . -xdev | cpio -pm /mnt/newroot
another way to copy everything from / to /mnt/newroot could becp -ax / /mnt/newroot
- You should modify the
/mnt/newroot/etc/fstabfile to use the correct device (the/dev/md?root device) for the root filesystem. - Now, unmount the current
/bootfilesystem, and mount the boot device on/mnt/newroot/bootinstead. This is required for LILO to run successfully in the next step. - Update
/mnt/newroot/etc/lilo.confto point to the right devices. The boot device must still be a regular disk (non-RAID device), but the root device should point to your new RAID. When done, runlilo -r /mnt/newroot
This LILO run should complete with no errors. - Reboot the system, and watch everything come up as expected :)
If you're doing this with IDE disks, be sure to tell your BIOS that all disks are "auto-detect" types, so that the BIOS will allow your machine to boot even when a disk is missing.
Method 2
This method requires that your kernel and raidtools understand the
failed-disk directive in the /etc/raidtab file - if you are
working on a really old system this may not be the case, and you will
need to upgrade your tools and/or kernel first.
You can only use this method on RAID levels 1 and above, as the method uses an array in "degraded mode" which in turn is only possible if the RAID level has redundancy. The idea is to install a system on a disk which is purposely marked as failed in the RAID, then copy the system to the RAID which will be running in degraded mode, and finally making the RAID use the no-longer needed "install-disk", zapping the old installation but making the RAID run in non-degraded mode.
- First, install a normal system on one disk (that will later become part of your RAID). It is important that this disk (or partition) is not the smallest one. If it is, it will not be possible to add it to the RAID later on!
- Then, get the kernel, the patches, the tools etc. etc. You know the drill. Make your system boot with a new kernel that has the RAID support you need, compiled into the kernel.
- Now, set up the RAID with your current root-device as the
failed-diskin the/etc/raidtabfailed-diskas the first disk in theraidtab, that will give you problems with starting the RAID. Create the RAID, and put a filesystem on it. If using mdadm, you can create a degraded array just by running something likemdadm -C /dev/md0 --level raid1 --raid-disks 2 missing /dev/hdc1, note themissingparameter. - Try rebooting and see if the RAID comes up as it should
- Copy the system files, and reconfigure the system to use the RAID as root-device, as described in the previous section.
- When your system successfully boots from the RAID, you can
modify the
/etc/raidtabfailed-diskas a normalraid-disk. Now,raidhotaddthe disk to your RAID. - You should now have a system that can boot from a non-degraded RAID.
7.5 Making the system boot on RAID
For the kernel to be able to mount the root filesystem, all support for the device on which the root filesystem resides, must be present in the kernel. Therefore, in order to mount the root filesystem on a RAID device, the kernel must have RAID support.
The normal way of ensuring that the kernel can see the RAID device is to simply compile a kernel with all necessary RAID support compiled in. Make sure that you compile the RAID support into the kernel, and not as loadable modules. The kernel cannot load a module (from the root filesystem) before the root filesystem is mounted.
However, since RedHat-6.0 ships with a kernel that has new-style RAID support as modules, I here describe how one can use the standard RedHat-6.0 kernel and still have the system boot on RAID.
Booting with RAID as module
You will have to instruct LILO to use a RAM-disk in order to achieve
this. Use the mkinitrd command to create a ramdisk containing
all kernel modules needed to mount the root partition. This can be
done as:
mkinitrd --with=<module> <ramdisk name> <kernel>For example:
mkinitrd --preload raid5 --with=raid5 raid-ramdisk 2.2.5-22
This will ensure that the specified RAID module is present at boot-time, for the kernel to use when mounting the root device.
Modular RAID on Debian GNU/Linux after move to RAID
Debian users may encounter problems using an initrd to mount their root filesystem from RAID, if they have migrated a standard non-RAID Debian install to root on RAID.
If your system fails to mount the root filesystem on boot (you will see this in a "kernel panic" message), then the problem may be that the initrd filesystem does not have the necessary support to mount the root filesystem from RAID.
Debian seems to produce its initrd.img files on the
assumption that the root filesystem to be mounted is the current one.
This will usually result in a kernel panic if the root filesystem is
moved to the raid device and you attempt to boot from that device
using the same initrd image. The solution is to use the
mkinitrd command but specifying the proposed new root
filesystem. For example, the following commands should create and set
up the new initrd on a Debian system:
% mkinitrd -r /dev/md0 -o /boot/initrd.img-2.4.22raid % mv /initrd.img /initrd.img-nonraid % ln -s /boot/initrd.img-raid /initrd.img"
7.6 Converting a non-RAID RedHat System to run on Software RAID
This section was written and contributed by Mark Price, IBM. The text has undergone minor changes since his original work.
Notice: the following information is provided "AS IS" with no representation or warranty of any kind either express or implied. You may use it freely at your own risk, and no one else will be liable for any damages arising out of such usage.
Introduction
The technote details how to convert a linux system with non RAID devices to run with a Software RAID configuration.
Scope
This scenario was tested with Redhat 7.1, but should be applicable to any release which supports Software RAID (md) devices.
Pre-conversion example system
The test system contains two SCSI disks, sda and sdb both of of which are the same physical size. As part of the test setup, I configured both disks to have the same partition layout, using fdisk to ensure the number of blocks for each partition was identical.
DEVICE MOUNTPOINT SIZE DEVICE MOUNTPOINT SIZE /dev/sda1 / 2048MB /dev/sdb1 2048MB /dev/sda2 /boot 80MB /dev/sdb2 80MB /dev/sda3 /var/ 100MB /dev/sdb3 100MB /dev/sda4 SWAP 1024MB /dev/sdb4 SWAP 1024MBIn our basic example, we are going to set up a simple RAID-1 Mirror, which requires only two physical disks.
Step-1 - boot rescue cd/floppy
The redhat installation CD provides a rescue mode which boots into linux from the CD and mounts any filesystems it can find on your disks.
At the lilo prompt type
lilo: linux rescue
With the setup described above, the installer may ask you which disk your root filesystem in on, either sda or sdb. Select sda.
The installer will mount your filesytems in the following way.
DEVICE MOUNTPOINT TEMPORARY MOUNT POINT /dev/sda1 / /mnt/sysimage /dev/sda2 /boot /mnt/sysimage/boot /dev/sda3 /var /mnt/sysimage/var /dev/sda6 /home /mnt/sysimage/home
Note: - Please bear in mind other distributions may mount your filesystems on different mount points, or may require you to mount them by hand.
Step-2 - create a /etc/raidtab file
Create the file /mnt/sysimage/etc/raidtab (or wherever your real /etc file system has been mounted.
For our test system, the raidtab file would like like this.
raiddev /dev/md0
raid-level 1
nr-raid-disks 2
nr-spare-disks 0
chunk-size 4
persistent-superblock 1
device /dev/sda1
raid-disk 0
device /dev/sdb1
raid-disk 1
raiddev /dev/md1
raid-level 1
nr-raid-disks 2
nr-spare-disks 0
chunk-size 4
persistent-superblock 1
device /dev/sda2
raid-disk 0
device /dev/sdb2
raid-disk 1
raiddev /dev/md2
raid-level 1
nr-raid-disks 2
nr-spare-disks 0
chunk-size 4
persistent-superblock 1
device /dev/sda3
raid-disk 0
device /dev/sdb3
raid-disk 1
Note: - It is important that the devices are in the correct
order. ie. that /dev/sda1 is raid-disk 0 and
not raid-disk 1. This instructs the md driver to sync
from /dev/sda1, if it were the other way around it
would sync from /dev/sdb1 which would destroy your
filesystem.
Now copy the raidtab file from your real root filesystem to the current root filesystem.
(rescue)# cp /mnt/sysimage/etc/raidtab /etc/raidtab
Step-3 - create the md devices
There are two ways to do this, copy the device files from /mnt/sysimage/dev or use mknod to create them. The md device, is a (b)lock device with major number 9.
(rescue)# mknod /dev/md0 b 9 0 (rescue)# mknod /dev/md1 b 9 1 (rescue)# mknod /dev/md2 b 9 2
Step-4 - unmount filesystems
In order to start the raid devices, and sync the drives, it is necessary to unmount all the temporary filesystems.
(rescue)# umount /mnt/sysimage/var (rescue)# umount /mnt/sysimage/boot (rescue)# umount /mnt/sysimage/proc (rescue)# umount /mnt/sysimagePlease note, you may not be able to umount
/mnt/sysimage. This problem can be caused by the rescue
system - if you choose to manually mount your filesystems instead of
letting the rescue system do this automatically, this problem should
go away.
Step-5 - start raid devices
Because there are filesystems on /dev/sda1, /dev/sda2 and /dev/sda3 it is necessary to force the start of the raid device.
(rescue)# mkraid --really-force /dev/md2
You can check the completion progress by cat'ing the /proc/mdstat file. It
shows you status of the raid device and percentage left to sync.
Continue with /boot and /
(rescue)# mkraid --really-force /dev/md1 (rescue)# mkraid --really-force /dev/md0
The md driver syncs one device at a time.
Step-6 - remount filesystems
Mount the newly synced filesystems back into the /mnt/sysimage mount points.
(rescue)# mount /dev/md0 /mnt/sysimage (rescue)# mount /dev/md1 /mnt/sysimage/boot (rescue)# mount /dev/md2 /mnt/sysimage/var
Step-7 - change root
You now need to change your current root directory to your real root file system.
(rescue)# chroot /mnt/sysimage
Step-8 - edit config files
You need to configure lilo and /etc/fstab appropriately to boot from and mount
the md devices.
Note: - The boot device MUST be a non-raided device. The root device is your new md0 device. eg.
boot=/dev/sda
map=/boot/map
install=/boot/boot.b
prompt
timeout=50
message=/boot/message
linear
default=linux
image=/boot/vmlinuz
label=linux
read-only
root=/dev/md0
Alter /etc/fstab
/dev/md0 / ext3 defaults 1 1 /dev/md1 /boot ext3 defaults 1 2 /dev/md2 /var ext3 defaults 1 2 /dev/sda4 swap swap defaults 0 0
Step-9 - run LILO
With the /etc/lilo.conf edited to reflect the new
root=/dev/md0 and with /dev/md1 mounted as
/boot, we can now run /sbin/lilo -v on the chrooted
filesystem.
Step-10 - change partition types
The partition types of the all the partitions on ALL Drives which are used by the md driver must be changed to type 0xFD.
Use fdisk to change the partition type, using option 't'.
(rescue)# fdisk /dev/sda (rescue)# fdisk /dev/sdb
Use the 'w' option after changing all the required partitions to save the partion table to disk.
Step-11 - resize filesystem
When we created the raid device, the physical partion became slightly smaller because a second superblock is stored at the end of the partition. If you reboot the system now, the reboot will fail with an error indicating the superblock is corrupt.
Resize them prior to the reboot, ensure that the all md based filesystems are unmounted except root, and remount root read-only.
(rescue)# mount / -o remount,ro
You will be required to fsck each of the md devices. This is the reason for remounting root read-only. The -f flag is required to force fsck to check a clean filesystem.
(rescue)# e2fsck -f /dev/md0
This will generate the same error about inconsistent sizes and possibly corrupted superblock.Say N to 'Abort?'.
(rescue)# resize2fs /dev/md0
Repeat for all /dev/md devices.
Step-12 - checklist
The next step is to reboot the system, prior to doing this run through the checklist below and ensure all tasks have been completed.
- All devices have finished syncing. Check
/proc/mdstat /etc/fstab/etc/lilo.confhas beeb edited to reflect root device change./sbin/lilohas been run to update the boot loader.- The kernel has both SCSI and RAID(MD) drivers built into the kernel.
- The partition types of all partitions on disks that are part of an md device have been changed to 0xfd.
- The filesystems have been fsck'd and resize2fs'd.
Step-13 - reboot
You can now safely reboot the system, when the system comes up it will auto discover the md devices (based on the partition types).
Your root filesystem will now be mirrored.
7.7 Sharing spare disks between different arrays
When running mdadm in the follow/monitor mode you can make different arrays share spare disks. That will surely make you save storage space without losing the comfort of fallback disks.
In the world of software RAID, this is a brand new never-seen-before feature: for securing things to the point of spare disk areas, you just have to provide one single idle disk for a bunch of arrays.
With mdadm is running as a daemon, you have an agent polling arrays at regular intervals. Then, as a disk fails on an array without a spare disk, mdadm removes an available spare disk from another array and inserts it into the array with the failed disk. The reconstruction process begins now in the degraded array as usual.
To declare shared spare disks, just use the spare-group parameter
when invoking mdadm as a daemon.
7.8 Pitfalls
Never NEVER never re-partition disks that are part of a running RAID. If you must alter the partition table on a disk which is a part of a RAID, stop the array first, then repartition.
It is easy to put too many disks on a bus. A normal Fast-Wide SCSI bus can sustain 10 MB/s which is less than many disks can do alone today. Putting six such disks on the bus will of course not give you the expected performance boost. It is becoming equally easy to saturate the PCI bus - remember, a normal 32-bit 33 MHz PCI bus has a theoretical maximum bandwidth of around 133 MB/sec, considering command overhead etc. you will see a somewhat lower real-world transfer rate. Some disks today has a throughput in excess of 30 MB/sec, so just four of those disks will actually max out your PCI bus! When designing high-performance RAID systems, be sure to take the whole I/O path into consideration - there are boards with more PCI busses, with 64-bit and 66 MHz busses, and with PCI-X.
More SCSI controllers will only give you extra performance, if the SCSI busses are nearly maxed out by the disks on them. You will not see a performance improvement from using two 2940s with two old SCSI disks, instead of just running the two disks on one controller.
If you forget the persistent-superblock option, your array may not start up willingly after it has been stopped. Just re-create the array with the option set correctly in the raidtab. Please note that this will destroy the information on the array!
If a RAID-5 fails to reconstruct after a disk was removed and re-inserted, this may be because of the ordering of the devices in the raidtab. Try moving the first "device ..." and "raid-disk ..." pair to the bottom of the array description in the raidtab file.
Next Previous Contents